Taleya

Hi all. I got the tank overflow conundrum sorted, complete with a three way tap so I can run overflow to the gutter or to a storage bin to track to other tanks. Lotta swearing, handful of dodgy chinese parts and a lotta fun

Of course me being me I couldn't fckin stop there, and have built in a float system, so if the bin hits capacity it automatically diverts everything else to the stormwater - but I'm not too happy with the flow through the float. It's definitely limiting.

Anyone rec a wide bore low pressure float? There's like,maybe half a bar of pressure on this thing, so it really needs to be something that's gonna let everything through until it bobs up and shuts off.

current one in use

Working on the never-ending basement brewery and we have this: old piping installation holes, leading into the kitchen above.

That grey subfloor is asbestos hardiboard. We are going to eventually redo the kitchen - just not this year (priorities, man!) what would be the best way to cover this from the basement side? gut says just gluepaint to encapsulate and a piece of ply to hide the holes, sound idea?

Edit: ok cos there seems to be repeated confusion: These are holes in the CEILING of a basement brewery leading to the asbestos floored kitchen ABOVE.

Ok chucklefucks i hope you like homebrew!

We currently have a set of maze tanks down the side of the house. They fill up pretty rapidly, so when we're looking at good rainfall i swap the overflow out to an old greywater wheeliebin to pump to other tanks / use in garden. You can see the temp setup from yesterday's rain - the flow to stormwater is on the right, the temp plugged vinidex to the bin on the left

I'm looking to make this process easier than plugging/unplugging plumbing, so was planning on putting in a T with the side to an outlet I can clip an18mm hose onto for the bin, and the down with a ball valve underneath (then leading to the stormwater to cut over to binfill vs stormwater as opposed to my current screw/unscrew/can't curve the poly that much so it takes up half the pathway. Simples, yes?

But then i had An Idea. The top links between the tanks are a PITA. Always dribbling, don't feed through very much, would be a gigantic pain to redo as they're very tight and the bottom link is cemented...so what if i tied in the bottom link (white pipe at the bottom left) at a slightly lower height than that top overflow, which would stop the top links hitting regular capacity, but be able to use them during high flood.

So: standpipe from bottom linking pipe to tie into the top overflow, then work in a tee and a valve so I can cut over the flow from stormwater to bin....workable?

cross-posted from: https://aussie.zone/post/15458542

I made a spreadsheet on info and pricing for every mobile plan in Australia (that I could find)

Made a spreadsheet of mobile plan data so people could compare providers and plans easily. I plan to update it either yearly or every 6 months. This was inspired by this spreadsheet on all the NBN plan pricing information: https://docs.google.com/spreadsheets/d/1_wnaTFb_3QsdgZfKDrEO6D_Rpzt2clbB/edit?gid=1523306688#gid=1523306688

In just over two years, their small Hamilton-based business, Sustainable Plastic Solutions, has reclaimed 3,000 tonnes of plastic and has created a world-leading closed-loop circular economy for grain tarpaulins.

They've just received a federal grant for matched funding of $9 million that will expand their operations to 16,000 tonne capacity per year and should enable them to tackle the so-far-unsolvable problem of recycling silage wrap.

But in the beginning, it was all financed by local farmers.

ok, so looking to get a rotary hammer drill. SDS / chuck, I don't care, can kinda go either way with corded/cordless - would prefer the latter, but well aware you lose balls with a battery.

I've been eyeing off the Ryobi HP brushless SDS (RSDS18X) but I think it's mostly the shiny factor and the fact we're already in the ecosystem - which I can happily toss in a bin if something better and cheaper comes along. It is the upper limit of the budget though, so call that a benchmark. Yes I will be shopping at the big green shed.

I already have two standard drills, an impact driver and a hammer drill, so as you can imagine the rotary will be used for situations where I am Done Asking Politely (and I have a lot of concrete I shall be negotiating with)

REC ME O WISE ONES

Marble outdoor to internal hardwood. House built in the 60's and i just spent ages clearing up old carpet tack and cement some dickhead had slapped over the floorboards.

It's not even, but hangs around 3cm difference between flooring surfaces. The surrounding walls are original bullnose sideboards in spectacular condition, so would like to be sympathetic.

Ideas? Suggestions?

(Yes i'm treating the rot and putting in a moisture break between the cement and wood)

Due to hardware reqs we're tossing the idea at work to replace the Microsoft termserv with Linux. Due to the userbase being all windows fans we'd need a full on GUI and i've been prodded towards Mint. Good idea or bad?

I've happily set up a remote kunbuntu for my workspace previously, but accomodating multiple complete linux neophytes is giving me a bit of pause.

Bit more info: The current termserv is a debloated win10 machine with the multisession registry edit. However, it's on an R515 with proxmox (and running extremely well). Due to partner network requirements, we can't run depreciated software, and the box won't support win11, and frankly, I sat the boss down and asked him if he wanted to be microsoft's bitch for the forseeable future and junk serviceable hardware. He's absolutely up to getting on a linux ecosystem, but the graphical desktop environment is non-negotiable on his end.

**EDIT: ** Anyone else looking to run this system: https://www.apalrd.net/posts/2022/xrdp_intro/ Video link at https://www.youtube.com/watch?v=sAllRma_0xc

Stumbled across https://www.bulkbuys.com.au/ earlier today, has some good stuff if anyone's interested.

Based on an r210 II I'm currently doing up

• Orico HB-325 3.5 to 2.5 inch Hard Drive Caddy - don't even bother. Could be useful in a CRU sled, but I don't have a dell one to hand.
• SilverStone SDP08B 3.5" to 2 x 2.5" Drive Bay Converter Getting better, but all four screws don't align in the dell caddy
• SilverStone SDP08B, 3.5" to 3 x 2.5" Drive Bay Converter Absolutely perfect.

random info I thought may be useful to others

Tim Pallas told an industry breakfast on Tuesday that he planned to introduce legislation to parliament this week, which will see the vacant residential land tax expanded to include the whole state from 1 January 2025.